路由器故障：MP Group成員接口狀態頻繁Up/Down
MP Group成員接口狀態頻繁Up/Down的故障解決步驟如下：
網絡環境
兩臺NE40路由器RouterA和RouterB通過MP Group鏈路連接，MP Group由8條E1鏈路捆綁而成。如圖所示。
MP Group故障組網圖
在進行一次設備調整后，發現業務不通，查看接口發現MP Group成員不停地Up/Down，MP Group自身也有Up/Down現象。
查看日志緩沖區，可以看到有很多Serial口和MP Group接口Up/Down的日志信息：
- %Jul 21 04:06:48 2007 A2 LSPM/5/LSPM:
- Info:[LSPM] Get interface event 1 and address 0x0 for interface Mp-group1/1/1
- %Jul 21 04:06:48 2007 A2 IFNET/5/UPDOWN:Interface Serial1/1/3:0 Turns into DOWN state
- %Jul 21 04:06:48 2007 A2 LSPM/5/LSPM:
- Info:[LSPM] Get interface event 1 and address 0x0 for interface Mp-group1/1/1
- %Jul 21 04:06:48 2007 A2 IFNET/5/UPDOWN:Interface Serial1/1/2:0 Turns into DOWN state
- %Jul 21 04:06:48 2007 A2 LSPM/5/LSPM:
- Info:[LSPM] Get interface event 1 and address 0x0 for interface Mp-group1/1/1
- %Jul 21 04:06:48 2007 A2 IFNET/5/UPDOWN:Interface Serial1/1/1:0 Turns into DOWN state
- %Jul 21 04:06:48 2007 A2 LSPM/5/LSPM:
- Info:[LSPM] Get interface event 1 and address 0x0 for interface Mp-group1/1/1
- %Jul 21 04:06:48 2007 A2 IFNET/5/UPDOWN:Interface Serial1/1/0:0 Turns into DOWN state
- %Jul 21 04:06:48 2007 A2 LSPM/5/LSPM:
- Info:[LSPM] Get interface event 1 and address 0x0 for interface Mp-group1/1/1
- %Jul 21 04:06:47 2007 A2 IFNET/5/UPDOWN:Line protocol(MPLSCP) on interface Mp-group1/1/1, changed state to UP
- %Jul 21 04:06:47 2007 A2 RM/4/RMLOG:OSPF PhyIf Info: IfName: Mp-group1/1/1, P1: 4d, P2: 400088e, P3: 3, P4: 10240000, P5: 1500, P6: 4
- %Jul 21 04:06:47 2007 A2 RM/4/RMLOG:OSPF LogicIf Info: IfName: Mp-group1/1/1, P1: 21, P2: 77, P3: 67111054, P4: 3, P5: 10240000, P6: 1500, P7: 4
- %Jul 21 04:06:47 2007 A2 RM/4/RMLOG:OSPF PhyIf Info: IfName: Mp-group1/1/1, P1: 4d, P2: 400088e, P3: 3, P4: 10240000, P5: 1500, P6: 6
- %Jul 21 04:06:47 2007 A2 IFNET/5/UPDOWN:Line protocol(OSICP) on interface Mp-group1/1/1, changed state to UP
- %Jul 21 04:06:47 2007 A2 IFNET/5/UPDOWN:Line protocol(MPLSCP) on interface Mp-group1/1/1, changed state to DOWN
故障分析
步驟 1 檢查鏈路兩端NE40的配置，發現配置沒有異常。
步驟 2 由于設備調整后鏈路中斷，設備重起后PPP需要重新協商，可能出現協商不成功，重啟接口板后發現問題依然存在。
步驟 3 執行命令display interface mp-group，查看接口信息，發現兩端路由器上的MP group的成員接口中有一些處在Active狀態，另一些處在Inactive狀態，并且狀態不停的變化，而正常情況下應該都是Active。同時發現Peer IP address協商異常。顯示的接口信息如下：
- <A2> display interface mp-group1/1/1
- Mp-group1/1/1 current state: up,
- Line protocol current state: up
- Description: to_B2_MPgroup1/0/1
- Internet address is 10.240.240.5/30
- Link-protocol is PPP, MP, NO SHORTSEQUENCE, DISCRIMINATOR
- MRRU 1500 bytes, Peer MRRU 1500 bytes
- The Max HQOS BandWidth is 9520 Kbits
- Include: 5 * E1, Active: 4 * E1
- Serial1/1/4:0 A
- Serial1/1/3:0 A
- Serial1/1/2:0 A
- Serial1/1/1:0 A
- Serial1/1/0:0 I
- Peer IP address is 10.240.240.2/32
- NCP: IPCP Opened, OSICP Opened, MPLSCP Opened
- <A1> display interface mp-group1/1/1
- Mp-group1/1/1 current state: up,
- Line protocol current state: up
- Description:to_B1_MPgroup1/0/1
- Internet address is 10.240.240.1/30
- Link-protocol is PPP, MP, NO SHORTSEQUENCE, DISCRIMINATOR
- MRRU 1500 bytes, Peer MRRU 1500 bytes
- The Max HQOS BandWidth is 9520 Kbits
- Include: 5 * E1, Active: 3 * E1
- Serial1/1/4:0 A
- Serial1/1/3:0 A
- Serial1/1/2:0 I
- Serial1/1/1:0 A
- Serial1/1/0:0 I
- Peer IP address is 10.240.240.6/32
- NCP: IPCP Opened, OSICP Opened, MPLSCP Opened
步驟 4 通過上面顯示的信息可以判斷，這是由于中間傳輸鏈路交叉連接，導致兩個MP Group交叉。
----結束
處理步驟
步驟 1 檢查傳輸線路，找到傳輸連接交叉的線路，調整傳輸線路。
步驟 2 觀察路由器上MP Group鏈路的狀態，保持在Up狀態，故障得到排除。
----結束
案例總結
在處理MP Group鏈路的故障時，也要檢查中間傳輸線路的故障。
【編輯推薦】
- 路由器故障：CE1接口網速較慢
- 路由器故障：POS口狀態反復Up/Down
- 路由器故障：POS接口修改MTU值無法生效
- 路由器故障：POS接口無法收到對端的報文
- 路由器故障：POS鏈路不能Up：C2字節不匹配
